Bighorn Forge's Weblog

"Credit goes to the man who is actually in the arena"…T. Roosevelt

  • Archives

Restored Twin Gates Receive Gold Medal

Posted by bighornforge on April 7, 2015


Edgar Brandt Gate, restored in 2014 by Dan Nauman, and Finelli Ironworks.

Edgar Brandt Gate, restored in 2014 by Dan Nauman, and Finelli Ironworks.

NOMMA 2015 Top Job Award

Jim Korosec of “Finelli Ironworks”, contacted me a few years ago to help his company restore two sets of identical gates in Cleveland, Ohio.  That was the beginning of a long, interesting, and sometimes trying journey.

I am pleased to announce that through a combined effort with “Finnelli Ironworks” of Solon, Ohio, a gold medal was awarded for both our efforts last month by the “National Ornamental and Miscellaneous Metals Assoc.” (NOMMA), at their annual “Top Job” competition. As only one company can enter for a given project, only “Finelli Ironworks” was recognized, however “Bighorn Forge. Inc.” will receive a duplicate gold medal along with a certificate.

Gate detail- rosette

Gate detail- rosette

We reproduced all of the rosettes, husks, and acanthus leaves for these gates, primarily using the French repousse’ method of metal forming.  The original pieces were machine stamped.

I was assisted in part by Jeremiah Backhaus, who helped make the 100 compound rosettes (50 compound rosettes per gate, 200 total pieces.)  Some are near the top of the gate, all in a row, and some are at about waist height, all in a row (see image below.)

Gate detail- compound rosettes, 100 total

Gate detail- compound rosettes, 100 total

Gate detail-square compound rosettes, 64 total

Gate detail-square compound rosettes, 64 total

This effort took well over 1100 hours, and resulted in two carpal tunnel surgeries for me.  To give you an idea as to how much time is invested in each piece, each compound square rosette above has about 5-1/2 hours invested x 64 sets.  That equates to 352 hours, just for this series of pieces.

Gate detail- top

Gate detail- top

These gates were originally made by master blacksmith Edgar Brandt (1880-1960) of France, who made and shipped them for the estate of “Harvey Firestone, Jr.” in Cleveland, Ohio. (Original photo below.)

Image of Edgar Brandt gate, taken shortly after original installation

Image of Edgar Brandt gate, taken shortly after original installation

Harvey_Firestone

Harvey Firestone, Jr.

In order to reproduce these many forms, there was extensive research into the original pattern development, which was difficult as many original pieces were so rusted away, that only fragments remained, as the images below demonstrates.

Pattern development, based on remnants

Pattern development, based on remnants

Recreated acanthus leaf pattern, approx. 16" x 49"

Recreated acanthus leaf pattern, approx. 16″ x 49″

The image above of the very large acanthus leaf pattern shows some of the remnants used to approximate the original pattern.  Note that the original “parrot’s beak” at the end (scroll-like termination) is missing entirely.  Five pattern changes on the parrot’s beak, along with three test pieces, were made before settling on one that proved to work well.

Below are some images of some of the many reproductions.

Husks- 16 total pcs. Note pattern in the foreground.

Husks- 16 total pcs. Note pattern in the foreground.

Compound rosettes, eight total sets.

Compound rosettes, eight total sets.

Various reproduced forms

Various reproduced forms

Some rosette sets for one gate.

Rosette sets for one gate.

Rosette #2 Repro and Original

Original machine stamped piece on right, hand formed reproduction on left.

I would like to thank Finelli Ironworks, and specifically Jim Korosec, for getting me involved in this project.  By the way, Jim found me via this blog site.  The owner of the gates was ready to fly to France to find someone who could reproduce these pieces by hand.  However, just prior to him leaving, Jim found me through this blog site, and e-mailed me about this project.  I responded, not expecting a reply from Jim, as I receive many such inquiries regarding parts made by French repousse’.  Typically, when folks realize the time it takes…consequently the monetary investment…they back off in a hurry.

However, Jim ended up calling me, and said the owner was going to fly to my shop the next day to meet with me.  Since I was driving out to Maine to teach repousse’ in just two weeks, I said that I would stop by (in Cleveland, Ohio) on my way back, so there was no need for the owner to fly to my studio. And so, I met with Jim and the owner in Cleveland in August of 2012. Obviously, they trusted that I could do the job.

Below are the very last part I made for this project, which are ribbon bows made of 20 gauge sheet metal.  There is roughly seven hours in each bow, of which there are four small and two large versions.  these proved to be some of the more challenging of the forms.  However it is challenges such as this that keep me returning to the studio.

Bows three

Three of the four small ribbon bows, approx. 20″ x 20″.

Original bow to the left, repro on right.

Original bow to the left, repro on right.

There is always a bittersweet end to such a journey.  I’ll admit, there were many times I was bouncing off the walls because of some of the repetitious aspects of this project. For example, when I was working on the square rosettes, of which there were 64, and it takes about 5-1/2 hours per rosette…when I got to rosette number 15, I was already seemingly headed for the loonie bin, wondering if I’d keep my sanity with so many like parts with so much detail.  The carpal tunnel symptoms didn’t help, either.

However, what kept me going was that I knew mentally prepared myself beforehand, knowing that I’d hit the proverbial wall at some point, and so I expected this monotony to happen…several times.  I also kept thinking that when the project was completed, I could stand in front of those gates, and have a fine feeling of accomplishment.

I also thank the owner of these gates for trusting in my abilities.  (I keep his name anonymous in respect of his privacy.)

And so it has ended, with that very satisfaction as my main reward.  I also learned a great deal during this process.  Lastly, i wish to thank the Lord my God for giving me the where-with-all to accomplish the task.

…Dan Nauman, April, 2015

“Leadership is the ability to transform vision into reality.”– Warren G. Bennis

3 Responses to “Restored Twin Gates Receive Gold Medal”

  1. Travis Fleming said

    Awesome work Dan!!
    Travis

  2. A.R. Gee said

    Overwhelmingly beautiful. What ardor, talent and fortitude. Thank you so much for sharing these images and the news of your well-deserved accolade!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

 
%d bloggers like this: