Bighorn Forge's Weblog

"Credit goes to the man who is actually in the arena"…T. Roosevelt

  • Archives

Archive for the ‘Decorative ironwork’ Category

“The Witch of November”

Posted by bighornforge on October 13, 2017


“The Witch of November”

I recently completed this maquette, designed for a client whose home overlooks Lake Michigan from atop the bluffs.  My goal was to capture the essence of the Autumn gales (swirling winds and water), dubbed “the witch of November” by the mariners of the Great Lakes region.

I had already made several drawings for the client of several different designs.  However, I wasn’t 100% excited about any of them, and consequently, I told them I was going back to the drawing board.

This design actually hit me in the wee hours of the night while lying in bed.  As not to forget the idea, I rose, and went down to the office to make notes.  The curious thing about this piece was that I typically make a scale drawing for my projects.  But I had the idea so solidly embedded in my head, with much anticipation, I embarked on the project the very next morning without a drawing.

I did make scale drawings on the layout table of some of the patterns, and did the math so each bar’s termination would end up in a specific spot.  However, I did want to take the project at a slow but sure pace, leaving a bit of spontaneous inspiration to come from the process itself…and I wasn’t disappointed.

The final forged piece, (the swirling ribbon as a centerpiece),  took some thought.  I tried various motifs, some very different to add contrast, and some going outside the box by starting inside and wrapping around the perimeter.  None seemed quite right, especially the latter which made the piece top-heavy.

Pondering again the winds and water, I was pushed to further reflect on the turbulence, yet the interaction of these elements that produce storms out on this great lake.  Then the idea of a volute form struck me, but with some contrast to the rest of the piece.  So I envisioned a ribbon, with texture to offset the otherwise smooth and flowing plate.  This seemed perfect, as it subtly represents the epicenter of a storm.

This piece is 1/2 scale of the proposed finished sculpture.  It is 16″ x 44″, so the final piece will stand about 88″ high.  The model is mainly of 1/2″ round mild steel, 1/8″ plate, with the centerpiece (see detail above) made of 3/4″ round. Black and silver Gilders Paste finish.

I also wanted the audience to have a intriguing view from any vantage point.  The intersecting lines, plus the positive space of the plate flowing around the piece gives the feeling of movement from all angles.

The full scale sculpture will incorporate 1″ bars, which will be a challenge, however very dynamic in the end.  That said, I am also giving the client the option of a 3/4 version at 66″ high, made with 3/4″ bars.

…Dan Nauman                                                                                                                                                        October, 2017

 

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork, Uncategorized | Leave a Comment »

Processional Cross

Posted by bighornforge on September 5, 2016


Processional Cross 3

Processional Cross.  17″ x 24″ x 96″.  Mild steel, Gilder’s Paste finish.  Main bars are 5/16″ square, and there are roughly 40 forge-welds in this project.  The French repousse” process was used to make the fleur-de-lis, rosettes, and button husks.  The 43″ tubular staff lifts off the base for processions.  made for St. peter’s Lutheran Church, Forestville, WI.

 

Processional Cross

           Processional Cross

Processional Cross Detail

 

Professional images will be taken and posted here in the near future.

 

…Dan Nauman

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork, Uncategorized | 4 Comments »

Birch Point Elk Antler Chandelier

Posted by bighornforge on May 28, 2016


BP Chand 6

 

This is the Birch Point Chandelier.  Designed and executed by Dan Nauman.  It was installed May 26, 2016 near Hayward in northern Wisconsin.  I was assisted in the installation by my assistant, Jeremiah Backhaus, who also helped me with some aspects of making this piece.  One of the owners, as well as his friend who did the timber frame work on this lodge (hand hewing and all), also helped with the install.BP Chand 7

The piece is approx. 72″ x 84″, with a 10-1/2′ drop.  It is made of mild steel, copper, slumped glass, and elk antler sheds.  I made almost every piece on this chandelier, through hand forging, and  French repousse’.  The exceptions were three collars that were bored out by a friend, as I did not have a large enough drill bit for my lathe, nor a boring bar.  I also had the patterns for the birch leaves laser cut by Muthig Industries in Fond du Lac, WI.  The stems were cut purposely wide, so I could forge them down to round.  I then hand-veined, then hot-sunk the leaves into a tree stump to give them volume and movement. The piece was sand-blasted, and has a poly-chrome paste finish.  John Abler, of Abler Art Glass in Kiel, WI (john@ablerartglass.com) made the two glass shades which are 10″ and 14″ in diameter.  The glass was slumped in sections, and leaded together to from a hemisphere.

BP Chand 12

 

The elk antler sheds came from Idaho, specifically: Yellowstone Antlers, Donovan Shipton (don@yellowstoneantlers.com).  Don did a fine job of finding three matched sets, that were relatively close in size from one set to the other.

BP Chand 15

 

The piece was wired by Zach Skarda at Heritage Lighting, Cedarburg, WI (zach@antiquelights.com).

 

BP Chand 4

 

The piece was sandblasted.  I then applied black Gilders Paste (TM).  Once dried, I polished the entire piece.  A second application of paste was applied to give the piece bronze highlights.  The image below better illustrates those highlights.

BP Chand Install 2 (2)

 

BP Chand 3

 

 

Once the piece was installed, the owners delighted us by giving us a tour of this fine lodge, designed to give the feeling of a 1940’s vintage east coast hunters lodge, complete with full bear mount, elk shoulder mount, a mammoth wood fireplace in the great room, and of course, a timber-frame log construction…of which was hand-hewed locally by artisans.  Further, they prepared a fine meal centered around a side of bison, prepared to your liking, asparagus, wild rice,  fine red wine, ice wine after supper, and also strawberry rhubarb pie and strawberry shortcake…all home-made, and all served beneath the warm glow of the newly installed elk-antler chandelier.

The evening was capped off by stories and yarns.  I awoke early the next morning (5:45), made coffee, and from the porch overlooking the lake, I watched the sun’s rise.  Serenaded by loons, and entertained by two otters, the morning started off perfectly.  Our hosts then prepared a fine breakfast, and again we dined under the light of the chandelier.  A delightful climax for a journey that began last December.

…Dan Nauman

28 May, 2016

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork | Leave a Comment »

“Console Table 2015” by Dan Nauman

Posted by bighornforge on July 31, 2015


Console Table 2015 C

Console Table 2015


The debut of “Console Table 2015” was last evening, at an event entitled, “Artist Bike Night” at the “Iron Horse Hotel” in Milwaukee, WI.  I was invited to exhibit there along with three other artists.  I must have seen over three hundred bikes…mainly Harley-Davidsons.  It was an enjoyable, and LOUD, evening.

This piece, 16 x 18 x 25-1/2 in, was inspired by the large acanthus leaf on the upper portion of the “S” scroll.  I had been wanting to make that leaf for several years.  So I finally made it last month, while visiting my friend Tom Latane’, a fine fellow and blacksmith in Pepin, WI.  Tom and I had been working on twin projects, two tin kitchens, on and off for the last couple years together.

Unfinished Tin Kitchen (a.k.a. "reflector oven")

Unfinished Tin Kitchen (a.k.a. “reflector oven”)

 

Well I finally finished mine, and thus I had a day or so to “play” in Tom’s shop before returning home, so I began to work on the leaf.

Console Table 2015 B

Upon finishing it, I thought it was too nice a piece to not have a home or function, so I designed the console table around the acanthus leaf.  Yes, this is backwards, as the leaf is usually the salt and pepper, not the main course.  However, that is how this piece evolved.  I initially designed this project to be a shelf bracket.  I worked a little on it one day, set it aside in the shop to work on a project that pays the bills.  I would glance at it every so often, and think, “What does this piece want added to it?”  So it evolved slowly to what you see here in these images.

This is definitely not how one should execute a project, however since this was a piece for me, and to be used as a display piece, I bent the rules a bit.  That said, I did have a full scale lay-out of the primary shape on the lay-out table.  Every so often, I would take a piece of soapstone and draw in another element.  The lay-out kept me honest, and the project sound.

One aspect of this project that I enjoyed was using copper for the repousse’ elements.  I typically use 18 gauge steel, but in this case I used 16 gauge copper.  It forms very easy compared to steel, as one might expect.  However, it also shows every hammer blow…on target or not.  That said, the errant blows are more easily erased in copper than those in steel.

Console Table 2105  A

 

 

The finish is primarily bee’s wax, however the table pan was finished with black “Gilders Paste”.  I plan on topping the pan with 3/4″ marble or granite.

By the way, if you ever wish to have a truly fine dining experience, I highly recommend “Smyth”, the restaurant located inside the “Iron Horse Hotel”.  I have dined there on several occasions, and every time the cuisine has been exceptional.  We ordered two hors-d’oeuvres; one was spiced goat cheese, and the other was  seasoned scallops on a bed of fresh corn.  The hotel and restaurant are a stone’s throw from Milwaukee’s “Harley Davidson Museum”.

…Dan Nauman

“Nobody goes there anymore…it’s too crowed”. – Yogi Berra, when asked about a local restaurant.

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork, Repousse' | 2 Comments »

Restored Twin Gates Receive Gold Medal

Posted by bighornforge on April 7, 2015


Edgar Brandt Gate, restored in 2014 by Dan Nauman, and Finelli Ironworks.

Edgar Brandt Gate, restored in 2014 by Dan Nauman, and Finelli Ironworks.

NOMMA 2015 Top Job Award

Jim Korosec of “Finelli Ironworks”, contacted me a few years ago to help his company restore two sets of identical gates in Cleveland, Ohio.  That was the beginning of a long, interesting, and sometimes trying journey.

I am pleased to announce that through a combined effort with “Finnelli Ironworks” of Solon, Ohio, a gold medal was awarded for both our efforts last month by the “National Ornamental and Miscellaneous Metals Assoc.” (NOMMA), at their annual “Top Job” competition. As only one company can enter for a given project, only “Finelli Ironworks” was recognized, however “Bighorn Forge. Inc.” will receive a duplicate gold medal along with a certificate.

Gate detail- rosette

Gate detail- rosette

We reproduced all of the rosettes, husks, and acanthus leaves for these gates, primarily using the French repousse’ method of metal forming.  The original pieces were machine stamped.

I was assisted in part by Jeremiah Backhaus, who helped make the 100 compound rosettes (50 compound rosettes per gate, 200 total pieces.)  Some are near the top of the gate, all in a row, and some are at about waist height, all in a row (see image below.)

Gate detail- compound rosettes, 100 total

Gate detail- compound rosettes, 100 total

Gate detail-square compound rosettes, 64 total

Gate detail-square compound rosettes, 64 total

This effort took well over 1100 hours, and resulted in two carpal tunnel surgeries for me.  To give you an idea as to how much time is invested in each piece, each compound square rosette above has about 5-1/2 hours invested x 64 sets.  That equates to 352 hours, just for this series of pieces.

Gate detail- top

Gate detail- top

These gates were originally made by master blacksmith Edgar Brandt (1880-1960) of France, who made and shipped them for the estate of “Harvey Firestone, Jr.” in Cleveland, Ohio. (Original photo below.)

Image of Edgar Brandt gate, taken shortly after original installation

Image of Edgar Brandt gate, taken shortly after original installation

Harvey_Firestone

Harvey Firestone, Jr.

In order to reproduce these many forms, there was extensive research into the original pattern development, which was difficult as many original pieces were so rusted away, that only fragments remained, as the images below demonstrates.

Pattern development, based on remnants

Pattern development, based on remnants

Recreated acanthus leaf pattern, approx. 16" x 49"

Recreated acanthus leaf pattern, approx. 16″ x 49″

The image above of the very large acanthus leaf pattern shows some of the remnants used to approximate the original pattern.  Note that the original “parrot’s beak” at the end (scroll-like termination) is missing entirely.  Five pattern changes on the parrot’s beak, along with three test pieces, were made before settling on one that proved to work well.

Below are some images of some of the many reproductions.

Husks- 16 total pcs. Note pattern in the foreground.

Husks- 16 total pcs. Note pattern in the foreground.

Compound rosettes, eight total sets.

Compound rosettes, eight total sets.

Various reproduced forms

Various reproduced forms

Some rosette sets for one gate.

Rosette sets for one of four gate leaves. (Above)

Rosette #2 Repro and Original

Original machine stamped piece on right, hand formed reproduction on left.

I would like to thank Finelli Ironworks, and specifically Jim Korosec, for getting me involved in this project.  By the way, Jim found me via this blog site.  The owner of the gates was ready to fly to France to find someone who could reproduce these pieces by hand.  However, just prior to him leaving, Jim found me through this blog-site, and e-mailed me about this project.  I responded, not expecting a reply from Jim, as I receive many such inquiries regarding parts made by French repousse’.  Typically, when folks realize the time it takes…consequently the monetary investment…they back off in a hurry.

However, Jim ended up calling me, and said the owner was going to fly to my shop the next day to meet with me.  Since I was driving out to Maine to teach repousse’ in just two weeks, I said that I would stop by (in Cleveland, Ohio) on my way back, so there was no need for the owner to fly to my studio. And so, I met with Jim and the owner in Cleveland in August of 2012. Obviously, they trusted that I could do the job.

Below are the very last parts I made for this project, which are ribbon bows made of 20 gauge sheet metal.  There is roughly seven hours in each bow, of which there are four small and two large versions. These proved to be some of the more challenging of the forms.  However it is challenges such as this that keep me returning to the studio.

Bows three

Three of the four small ribbon bows, approx. 20″ x 20″.

Original bow to the left, repro on right.

Original bow to the left, repro on right.

There is always a bittersweet end to such a journey.  I’ll admit, there were many times I was bouncing off the walls because of some of the repetitious aspects of this project. For example, when I was working on the square rosettes, of which there were 64, (and it takes about 5-1/2 hours per rosette)…when I got to rosette number 15, I was already seemingly headed for the loonie bin, wondering if I’d keep my sanity with so many like parts with so much detail.  The carpal tunnel symptoms didn’t help, either.

However, what kept me going was that I mentally prepared myself beforehand, knowing that I’d hit the proverbial wall at some point, and so I expected this monotony to happen…several times.  I also kept thinking that when the project was completed, I could stand in front of those gates, and have a fine feeling of accomplishment.

I also thank the owner of these gates for trusting in my abilities.  (I keep his name anonymous in respect of his privacy.)

And so it has ended, with that very satisfaction as my main reward.  I also learned a great deal during this process.  Lastly, I wish to thank the Lord my God for giving me the where-with-all to accomplish the task.

…Dan Nauman, April, 2015

“Leadership is the ability to transform vision into reality.”– Warren G. Bennis

Posted in Decorative ironwork, Repousse' | 3 Comments »

“Work Book of Patterns” (For Repousse’)

Posted by bighornforge on April 18, 2014


Acanthus Leaf Pattern #1

In continuing with my tribute to the late repousse’ artisan Nahum Hersom, I am including some of his repousse’ patterns in this blog.  I do this as Nahum, as well as his mentors Steven Molnar and Valentin Goelz, wanted this process to be carried on.  Here is Nahum’s dedication statement (I will both type this, as well as provide a photo of his actual hand-written statement):

“In fond memory and much appreciation I dedicate this book to these two men who dedicated their lives to this great art of repousse.  Mr. Steven Molnar   Mr. Valentin Goelz.  Both were European Craftsmen of the highest caliber, and the most patient of teachers.  Their motto “If we don’t teach the young craftsmen who will carry on.”  Sincerely,  Nahum Hersom.”

Hersom's Dedication Statement

This dedication was contained in a loose-leaf “book” that I bought from Nahum for fifty bucks back in 1994 when I was under his tutelage.  I believe that Nahum, as well as Mister’s Molnar and Goelz, would wish these patterns, and Nahum’s instruction, saved for posterity…and for all those young craftsmen Nahum spoke of in his dedication.  As I have stated before, I wish to continue in their tradition of sharing and teaching the processes of French repousse’ through this blog.

Please note:  This loose-leaf book was printed at a Kinko’s in Boise, Idaho in 1993 on 8-1/2″ x 17″ paper.  Since my scanner cannot copy anything over 8-1/2 x 11″, some of the patterns may be cut-off.  I will try to provide as many complete copies of those patterns that were cut-off as possible.

This next entry is on the backside of the dedication page, and reads:

“To the Craftsmen”

This “Work Book of Patterns” is a compiling “as not yet complete” of patterns which I have in my shop.  Some of these patterns are approx. 80 years old, others not that old, and a few as new as a month ago. However the design behind these patterns is hundreds of years old going back to Jean Tijou 1690-1710 a French Ironworker, repousse seems to have been developed in France, where it spread throughout Europe.  These patterns are representative of architectural styles and periods of history, and those Craftsmen I have known.  The style of the tools herein lend themselves to making, fine jewelry, to the largest of architectural embellishments or ornaments.  After all all metal work started with the hammer and anvil or stake.  Perhaps ornamental decoration is now in a revival, beauty in iron is a work of art, I for one hope it grows and lasts for a long, long, time.  “Nahum Hersom””   (Circa 1993).

Hersom's To the Craftsmen Statement

I will finish this post with a few more patterns.

…Dan Nauman

Hersom Patterns #3

Hersom Patterns #2

Posted in Decorative ironwork, Forging Processes, Repousse' | Tagged: | 1 Comment »

Forged Furniture by Dan Nauman

Posted by bighornforge on February 27, 2014


Foyer Table.  Mild steel.  Natural finish.  Private residence. Mequon, WI.

Foyer Table. Mild steel. Natural finish. Private residence. Mequon, WI.

Selected forged furniture, forged tables, and forged baker’s rack designed and created by Dan Nauman.

Plant Stand.  Mild steel.  Gilders Paste (TM) finish.  Artist's collection.

Plant Stand. Mild steel. Gilders Paste (TM) finish. Artist’s collection.

Coffee Table.  Mild steel.  Gilders Paste (TM) finish.  Artist's collection.

Coffee Table. Mild steel. Gilders Paste (TM) finish. Artist’s collection.

Baker's Rack.  Mild steel and glass.  Natural finish.  Private residence.  Delevan, WI.

Baker’s Rack. Mild steel and glass. Natural finish. Private residence. Delevan, WI.

Baker's Rack detail.

Baker’s Rack detail.

Coffee table.  Mild steel.  Natural finish.  Private residence, Waukesha, WI.

Coffee table. Mild steel. Natural finish. Private residence, Waukesha, WI.

Coffee Table.  Mild steel and glass. Natural finish.  Private residence.

Coffee Table. Mild steel and glass. Natural finish. Private residence.

Coffee Table.  Mild steel and marble.  Natural finish.  Eagle, WI.

Coffee Table. Mild steel and marble. Natural finish. Private residence, Eagle, WI.

Console.  Mild steel and marble.  Private residence, Eagle, WI.

Console. Mild steel and marble. Private residence, Eagle, WI.

Side Table.  Mild steel and tile.  Natural finish.  Shorewood, WI.

Side Table. Mild steel and tile. Natural finish. Shorewood, WI.

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork | 1 Comment »

Forged Sign Brackets by Dan Nauman

Posted by bighornforge on February 27, 2014


Sign Bracket.  Mild steel.  Painted finish.  "Sam Meyer Agency", Fond du Lac, WI.

Sign Bracket. Mild steel. Painted finish. “Sam Meyer Agency”, Fond du Lac, WI.

 

Selected forged sign brackets designed and created by Dan Nauman.

 

Sign Bracket.  Mild steel.  Painted finish.  "Blacksmith Inn B+B", Baileys Harbor, WI.

Sign Bracket. Mild steel. Painted finish. “Blacksmith Inn B+B”, Baileys Harbor, WI.

 

Street Sign.  Mild steel.  Painted finish.  Glendale, WI.

Street Sign. Mild steel. Painted finish. Glendale, WI.

 

Subdivision Sign.  Mild steel.  Plastic coating.  "Toldt Woods", Wauwatosa, WI.

Subdivision Sign. Mild steel. Plastic coating. “Toldt Woods”, Wauwatosa, WI.

 

Deleivery Sign.  Mild steel.  Before finish was applied.  Made for a private estate in Sister Bay, WI.

Deleivery Sign. Mild steel. Before finish was applied. Made for a private estate in Sister Bay, WI.

 

Delivery sign detail.

Delivery sign detail.

 

Methodist Church Sign.  Mild steel.  Painted finish.  "First United Methodist Church", Campbellsport, WI.

Methodist Church Sign. Mild steel. Painted finish. “First United Methodist Church”, Campbellsport, WI.

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork | Leave a Comment »

Forged Gates and Archways by Dan Nauman

Posted by bighornforge on February 27, 2014


Driveway Gate.  Mild steel.  Painted finish.  Port Washington, WI.

Driveway Gate. Mild steel. Painted finish. Port Washington, WI.

Selected forged gates and archways designed and created by Dan Nauman.  The above gate won a silver medal from the “National Ornamental and Miscellaneous Metals Association” (NOMMA) in 2007.  Below is a detail image.

Gate detail

Entrance Gate.  Mild steel.  Powder coat finish.  "Lynden Sculpture Garden", Milwaukee, WI.

Entrance Gate. Mild steel. Powder coat finish. “Lynden Sculpture Garden”, Milwaukee, WI.

The above driveway gate at “Lynden Sculpture Garden” in Milwuakee, won a bronze medal from NOMMA in 2013.  Below are detail images.

Lynd Ent Gate W to E Hori GL

This gate spans 26 feet, and is 14 feet tall.

Lynden Entrance Gate Mast GL

Spider Web Gate.  Mild steel.  Painted finish.  Private residence, Cedarburg, WI.

Spider Web Gate. Mild steel. Painted finish. Private residence, Cedarburg, WI.

The above “Spider Web Gate” was inspired as these master gardeners were also armchair entomologists.  As you review this image, you will see insect parts, i.e. abdomens, legs, and a spider’s web.

Poolside Gate.  Mild steel.  Painted finsish. Private residence, Mequon, WI.

Poolside Gate. Mild steel. Painted finsish. Private residence, Mequon, WI.

Detail of "Poolside Gate."

Detail of “Poolside Gate.”

Exit Gate.  Mild steel.  Painted finish.  "Lynden Sculpture Garden", Milwaukee, WI.

Exit Gate. Mild steel. Painted finish. “Lynden Sculpture Garden”, Milwaukee, WI.

Orchard Gate. Mild steel.  Painted finish.  Private residence, Port Washington, WI.

Orchard Gate. Mild steel. Painted finish. Private residence, Port Washington, WI.

Garden Gate.  Mild steel.  Private residence, Sister Bay, WI.

Garden Gate. Mild steel. Private residence, Sister Bay, WI.

Garden Gate latch detail.  Sister Bay, WI.

Garden Gate latch detail. Sister Bay, WI.

Garden Gate.  Mild steel.  Natural finish.  Artist's collection.

Garden Gate. Mild steel. Natural finish. Artist’s collection.

Archway.  Mild steel.  Powder coat finish.  "Carroll College" (now "Carroll University"), Waukesha, WI.

Archway. Mild steel. Powder coat finish. “Carroll College” (now “Carroll University”), Waukesha, WI.

Archway.  Mild steel. Painted finish. "Executive Residence.", Madison, WI.

Archway. Mild steel. Painted finish. “Executive Residence.”, Madison, WI.

Archway detail.  "Executive Residence", Madison, WI.

Archway detail. “Executive Residence”, Madison, WI.

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork | Leave a Comment »

Forged Railings by Dan Nauman

Posted by bighornforge on February 27, 2014


Bronze Railing.  "Lynden Sculpture Garden", Milwaukee, WI

Patio Railing. Silicon bronze.  Natural patina. “Lynden Sculpture Garden”, Milwaukee, WI

Selected forged railings designed and created by Dan Nauman.  The above railing won a gold medal from the “National Ornamental and Miscellaneous Metals Association” (NOMMA) in 2013.  The image below shows the verdigris patina that is evolviing after a few years.

L1190460

Grape Vine railing.  Mild steel, with Gilders Paste (TM) finish.

Grape Vine railing. Mild steel. Gilders Paste (TM) finish.  Private residence, Waukeshs, WI.

Detail of grape vine.

Detail of grape vine.

Prairie Railing for log home.

Balcony Railing.  Mild steel, natural and Gilders Paste (TM) finish.  Private residence, Elkhart Lake, WI.

Detail of Prairie Railing.

Detail of Balcony Railing.

Detail of Prairie Railing.

Detail of Balcony Railing.

Railing. Mild steel and stained glass.  Painted finish.  Private Residence, Milwaukee, WI.

Railing. Mild steel and stained glass. Painted finish. Private Residence, Milwaukee, WI.

Railing.  Mild steel.  Painted finish.  Estate of former WI Gov. Patrick Lucey.

Railing. Mild steel. Painted finish. Estate of former WI Gov. Patrick Lucey, River Hills, WI.

Porch Railing.  Mild steel.  Painted finish.  Private residence, Egg Harbor, WI.

Porch Railing. Mild steel. Painted finish. Private residence, Egg Harbor, WI.

Balcony Railing.  Mild steel.  Painted finish.  Private Residence, River Hills, WI.

Balcony Railing. Mild steel. Painted finish. Private Residence, River Hills, WI.

Balcony Railing.  Mild steel.  Painted finish.  Private residence, River Hills, WI.

Balcony Railing. Mild steel. Painted finish. Private residence, River Hills, WI.

A simple railing on limestone steps.  Mild steel.  Private Residence, Egg Harbor, WI.

A simple railing on limestone steps. Mild steel. Private Residence, Egg Harbor, WI.

Two Railing Panels.  Mild steel, powder coat finish.  Private Residence, Sister Bay, WI.

Two Railing Panels. Mild steel, powder coat finish. Private Residence, Sister Bay, WI.

The above railing panels were exterior railings for a patio overlooking Green Bay, on Lake Michigan.  Unfortunately, the client would not allow me to take photographs on location, so these are studio shots.  The sections below were for the same mansion, but a different patio.

On both railings, the panels shown had simple two-foot panels between to divide them, and also to give the eye a break from the flowing lines.

Two railing Panels.  There was one more ornate panel along with these two.  Mild steel.  Powder coat finish.  Private residence, Sister Bay, WI.

Two railing Panels. There was one more ornate panel along with these two. Mild steel. Powder coat finish. Private residence, Sister Bay, WI.

Indoor Pool Stair Rail.  Stainless steel.  Natural finish.  Private Residence, Sister Bay, WI.

Indoor Pool Stair Rail. Stainless steel. Natural finish. Private Residence, Sister Bay, WI.

The above indoor pool stair rail was from the same mansion as the railing panels above it.  I was not allowed to photograph this in place either, so this is a studio shot.  The stainless steel was acid etched to give teh finish a look of pewter.  Below is a detail shot.

Railing Sister Bay Pool Det 

Another simple railng.  Private residence,

Another simple railng. Mild steel. Natural finish. Private residence, Richfield, WI.

Posted in Bighorn Forge/Nauman Ironwork, Decorative ironwork | Leave a Comment »